In real life, we often encounter situations where the zipper pull is pulled down. Then, when the zipper pull is lost, how can it be put back? The following zipper manufacturer brings you zipper maintenance methods and other related knowledge.

Zipper pulls are a common occurrence in daily life, so how can we pull them back when they are lost? Below, the editor will provide you with relevant knowledge about zipper paper jams, zipper maintenance, etc.

How can I put the zipper back when it falls off?

After cutting the lighter, burn off the edge of the lighter to prevent it from falling off.

2. Pull the zipper pull into the teeth along the upward direction of the pull teeth. Pull the two ends of the tape (indicated by the arrows) together and pull outward (as shown in the picture). The zipper will follow the tension of the tape. Enter the teeth.

After pulling out the fabric, the slider has been installed.

4. Use diagonal pliers to pull out the excess teeth.

5. Install the top and bottom.

The above is a detailed explanation of how zipper manufacturers pay attention to the wear and tear of zipper heads.

Tips for handling zippers stuck to clothes

You may encounter a situation where the zipper gets stuck in the fabric of the counterfeit clothing when pulled, and the zipper cannot be moved or moved. At this point, do not use brute force to pull it hard; otherwise, it will become even tighter. The fabric stuck in the slider should be pulled out slowly, then the slider should be pulled back to its original position and pulled up slowly. Be patient and deal with it!

When you use the zipper technique, you should pay attention to the zipper, such as cutting the belly, removing teeth and skewing. If the zipper is loose and has teeth, you can tap the zipper head a few times with a small hammer to make the upper and lower teeth bite together tightly. Then you won't have to pull out the teeth again.

Don't fill various bags, pockets or wallets with zippers. When pulling the zipper, first align the teeth on both sides, then hold the zipper pull and gently pull it forward along the track without pulling too hard.

Zipper maintenance tips

When in normal use, please pay attention to issues such as abdominal detachment, tooth extraction and skewing on the zipper. If you encounter these problems, please repair them in time and do not pull hard. If the zipper is loose and has teeth, please gently tap the zipper head a few times with a small hammer to make the upper and lower chain teeth bite tightly, and then do not pull out the teeth.

Aluminum alloy zippers are more prone to corrosion, so they should be kept dry and protected from moisture to prevent the formation of white oxides on the aluminum teeth, which can cause the zippers to rust and extend their service life. However, it is also important to avoid contact with alkaline substances. During storage, it should be kept well-ventilated, not sealed, and not stored in a damp environment. If necessary, moisture-proof paper or dehumidifiers should be used. If the zipper is damp and pulled up, dry it in the sun, then apply some wax to the teeth of the zipper and fire it to make it very smooth.

When pulling the zipper, first align the teeth on both sides, then hold the zipper pull and gently pull it forward along the track. Do not pull it hard to avoid tooth misalignment, breakage and dislocation. If the zipper is a bun and the pull is not flexible, you can wipe it with a cloth and then apply a layer of white wax on the teeth.

4. For all kinds of bags, pockets or zipped wallets, do not fill them too full, otherwise it is very easy for the zipper to break the abdomen, cause teeth to come out, become crooked and the fabric to become soft.

Zipper repair method

1. If the iron edges on both sides of the zipper come off. Repair method instructions: You can fold one end of the staples inward to be parallel to the iron and straighten the other end. According to the length of the edge of the zipper iron, the excess part of the nail is cut off from the straight end. After cutting, the staples should be placed beside the original iron. The folded back is placed below, flush with the bottom edge of the zipper, and the other end is folded to the same point. Then, use a windbreaker needle to sew the two pieces back and forth tightly, and wrap the staples inside. The width should be equal to the original iron edge. The bottom edge of the staples should be tightly pulled onto the seam, the seam should be smooth, and then touch the wax. In an instant, the maintenance effect is the same as that of the original iron edge.

2. If the zipper is missing teeth. Maintenance method introduction: At the original tail, use a pointed tip or camera to open the zipper teeth and remove a few teeth. After installing the tooth removal component, gently press the tooth opening against the edge of the cloth with a pointed mouth. He can only bite people.

Sometimes the zipper cannot be pulled or cannot be pulled to the middle. This is because the teeth of the zipper are broken or the fibers of the tape are loose. If the teeth of the zipper are broken, you can straighten it with a steel needle, then flatten it, and then gently press the teeth of the zipper flat with a small pair of tweezers. The zipper is done. If the tape is loose, you can pull the mismatched tape and evenly arrange the teeth of the zipper. You can pull them.

There are two reasons why a zipper is not smooth: it's fine, but the chain teeth are rusty or contaminated with dirt; Secondly, the handle feet are clamped at the edge of the fabric, etc. The former only needs to be gently wiped with wax on both sides of the zipper to slide smoothly and freely. The latter should slowly return the key head to its original position and remove any foreign objects. The zipper should not be placed close to the monitor. As it has been used for a long time, the distance between the upper and lower parts of the zipper head can be changed by Jiangda or simply clamped up and down or left and right with pliers, but be careful not to apply too much force to avoid pinching.

5. If the zipper lock breaks, it can only be replaced.

6. If there is no damage, please follow these steps: First, use pliers to pull down the large teeth at the top of the zipper and move them on both sides. Then pull the zipper lock to the top; Then bring the two teeth together; Then lock the zipper into it (it's a bit difficult because the diameter of the metal zipper is relatively thick. If it's not set, cut a small hole on the line. Remember, don't cut it at its place to install the large teeth. Cut it at the top, otherwise the large teeth won't be installed). Finally, after zipping it up, just place the large teeth on top.

7. Tips for zipper slippage: If the zipper is damp, rusty or oxidized, it won't slide smoothly. When not in use, apply force, such as rubbing it back and forth with candles on the two rows of teeth and putting on a barbecue fire once. It will slide very smoothly when pulled.

8. If you pull the zipper, it will open by itself: This problem is because the puller has been pulled for too long and the opening is getting larger and larger. If you want to solve it temporarily, please use pliers to hold the tail of the pull head. Just pay attention to the tail, but be careful not to use too much force or pinch it. If it is to be completely solved, the slider needs to be replaced.